A Low-Voltage Electronically Tunable MOSFET-C Voltage-Mode First-Order All-Pass Filter Design

This paper presents a simple electronically tunable voltage-mode first-order all-pass filter realization with MOSFET-C technique. In comparison to the classical MOSFET-C filter circuits that employ active elements including large number of transistors the proposed circuit is only composed of a single two n-channel MOSFET-based inverting voltage buffer, three passive components, and one NMOS-based voltage-controlled resistor, which is with advantage used to electronically control the pole frequency of the filter in range 103 kHz to 18.3 MHz. The proposed filter is also very suitable for low-voltage operation, since between its supply rails it uses only two MOSFETs. In the paper the effect of load is investigated. In addition, in order to suppress the effect of non-zero output resistance of the inverting voltage buffer, two compensation techniques are also introduced. The theoretical results are verified by SPICE simulations using PTM 90 nm level-7 CMOS process BSIM3v3 parameters, where +/- 0.45 V supply voltages are used. Moreover, the behavior of the proposed filter was also experimentally measured using readily available array transistors CD4007UB by Texas Instruments

DCCII-Based Novel Lossless Grounded Inductance Simulators With No Element Matching Constrains

In 1996, the differential current conveyor (DCCII) was introduced as a versatile active element with current differencing capability. Therefore, in this study, the usefulness of the DCCII is shown on six novel lossless grounded inductance simulator circuits. Proposed circuits simultaneously employ minimum number of elements, i.e. single DCCII, one capacitor, and two resistors. No passive element matching restriction is needed and all solutions are electronically tunable in case that one of resistors is replaced by MOSFET-based voltage-controlled resistor. The internal structure of the active element has been implemented using the TSMC 0.25 um SCN025 CMOS process BSIM3v3.1 parameters. Firstly, the performance of the selected inductor simulator is evaluated and subsequently verified in the design of 5th-order high-pass ladder and 2nd-order frequency filters. In addition, experimental results using commercially available AD844/ADs are given to verify the theoretical analysis and SPICE simulations

Current and Voltage Mode Multiphase Sinusoidal Oscillators Using CBTAs

Current-mode (CM) and voltage-mode (VM) multiphase sinusoidal oscillator (MSO) structures using current backward transconductance amplifier (CBTA) are proposed. The proposed oscillators can generate n current or voltage signals (n being even or odd) equally spaced in phase. n+1 CBTAs, n grounded capacitors and a grounded resistor are used for nth-state oscillator. The oscillation frequency can be independently controlled through transconductance (gm) of the CBTAs which are adjustable via their bias currents. The effects caused by the non-ideality of the CBTA on the oscillation frequency and condition have been analyzed. The performance of the proposed circuits is demonstrated on third-stage and fifth-stage MSOs by using PSPICE simulations based on the 0.25 µm TSMC level-7 CMOS technology parameters

Realization of Resistorless Lossless Positive and Negative Grounded Inductor Simulators Using Single ZC-CCCITA

This paper is in continuation with the very recent work of Prasad et al. [14], wherein new realizations of grounded and floating positive inductor simulator using current differencing transconductance amplifier (CDTA) are reported. The focus of the paper is to provide alternate realizations of lossless, both positive and negative inductor simulators (PIS and NIS) in grounded form using z-copy current-controlled current inverting transconductance amplifier (ZC-CCCITA), which can be considered as a derivative of CDTA, wherein the current differencing unit (CDU) is reduced to a current-controlled current inverting unit. We demonstrate that only a single ZC-CCCITA and one grounded capacitor are sufficient to realize grounded lossless PIS or NIS. The proposed circuits are resistorless whose parameters can be controlled through the bias currents. The workability of the proposed PIS is validated by SPICE simulations on three RLC prototypes

Lossy/Lossless Floating/Grounded Inductance Simulation Using One DDCC

In this work, we present new topologies for realizing one lossless grounded inductor and two floating, one lossless and one lossy, inductors employing a single differential difference current conveyor (DDCC) and a minimum number of passive components, two resistors, and one grounded capacitor. The floating inductors are based on ordinary dual-output differential difference current conveyor (DO-DDCC) while the grounded lossless inductor is based one a modified dual-output differential difference current conveyor (MDO-DDCC). The proposed lossless floating inductor is obtained from the lossy one by employing a negative impedance converter (NIC). The non-ideality effects of the active element on the simulated inductors are investigated. To demonstrate the performance of the proposed grounded inductance simulator as an example, it is used to construct a parallel resonant circuit. SPICE simulation results are given to confirm the theoretical analysis

Current and Voltage Conveyors in Current- and Voltage-Mode Precision Full-Wave Rectifiers

In this paper new versatile precision full-wave rectifiers using current and/or voltage conveyors as active elements and two diodes are presented. The performance of these circuit solutions is analysed and compared to the opamp based precision rectifier. To analyze the behavior of the functional blocks, the frequency dependent RMS error and DC transient value are evaluated for different values of input voltage amplitudes. Furthermore, experimental results are given that show the feasibilities of the conveyor based rectifiers superior to the corresponding operational amplifier based topology

Study of Adjustable Gains for Control of Oscillation Frequency and Oscillation Condition in 3R-2C Oscillator

An idea of adjustable gain in order to obtain controllable features is very useful for design of tuneable oscillators. Several active elements with adjustable properties (current and voltage gain) are discussed in this paper. Three modified oscillator conceptions that are quite simple, directly electronically adjustable, providing independent control of oscillation condition and frequency were designed. Positive and negative aspects of presented method of control are discussed. Expected assumptions of adjustability are verified experimentally on one of the presented solution

Current-Mode Dual-Phase Precision Full-Wave Rectifier Using Current-Mode Two-Cell Winner-Takes-All (WTA) Circuit

In addition to the recently proposed full-wave rectifier by Prommee et al. using voltage-mode (VM)two-cell winner-takes-all (WTA) circuit, we present current-mode (CM) precision full-wave rectifier using CM two-cell WTA circuit. The popular Lazzaro’s CM WTA circuit has been employed for the purpose and there is no requirement of inverting the input signal. Also, dual complimentary phases of the output current signal are available from high-output impedance terminals for explicit utilization. As compared to many recently proposed CM rectifiers using complex active devices, e.g. dual-X current conveyor or universal voltage conveyor, our circuit is very compact and requires a total of 21 transistors. SPICE simulation results of the circuit implemented using 0.35 um TSMC CMOS technology are provided which verify the workability of the proposed circuit

Voltage-Mode All-Pass Filters Using Universal Voltage Conveyor and MOSFET-Based Electronic Resistors

The paper presents two novel realizations of voltage-mode first-order all-pass filters. Both circuits use single universal voltage conveyor (UVC), single capacitor, and two grounded resistors. Using the two NMOS transistors-based realizations of the electronic resistor with two symmetrical power supplies, presented all-pass filter circuits can be easily made electronically tunable. Proposed filter structures provide both inverting and non-inverting outputs at the same configuration simultaneously and they have high-input and low-output impedances that are desired for easy cascading in voltage-mode operations. The nonidealities of the proposed circuits are also analyzed and compared. The theoretical results of both circuits are verified by SPICE simulations using TSMC 0.35 μm CMOS process parameters. Based on the evaluation, the behavior of one of the circuits featuring better performance was also experimentally measured using the UVC-N1C 0520 integrated circuit